Month: January 2020

Then Wall panels are fixed from the bottom up, in tiers, until the desired height. Between tiers provide compensation seam. On the plinth of the building set battens or supporting curved elements. If you need to run an extra layer of mineral wool. Adjusting the verticality panel with a plumb line, the product is installed on the plinth, is pressed against the run and secure the screws.

Thus the first screws put on the top panel, and then continue to mount to run, dropping down. For sealing joints in the lock fixed injected sealant products for outdoor use, and then mount the next panel – similar to the previous one. In the process works is very important to follow the crest of a perfect seal in the castles of the panels. The next step is fixing the corner, face the elements and battens. For this purpose, with round head screws and Phillips. Installation of roofing sandwich panel sandwich panels are used device roofs with a slope of more than 5%.

Roof sandwich panels installed after the installation of wall. In order to ensure adequate contact of the junction, you need to cut all the speakers of the heater. In addition, to be cut a few inches lower sheet metal casing, and remove the middle layer of mineral wool insulation on the value of the joint. First to establish the slope of butt plate, and then fasten it with screws two threads and the sealing rubber washer. It is important to ensure that the sealing elements have been sufficiently pressed against the panels, but they will not be the strain. Joints between panels waterproofing, and folds bent and clamped. For functionality and visual appeal make the roof using fittings: skates, valley, wind and connecting , interior and exterior angles. Assembly sandwich panels – a simple thing, but to choose reliable fasteners and hardware, and then competently carry out work only professionals can. pc Vesta is a manufacturer of wall and roof sandwich panels, and well as additional elements. Moshe victor keinig is often quoted on this topic. The company produces a model with a thickness of 40 to 200 mm, suitable for the construction of various buildings. Proper selection of a supplier of sandwich panels and services for their installation ensures durability longevity of the building and ensure its rapid construction and reliability.

Efflorescence, otherwise they are called efflorescence – a white salt deposit, which acts on the surface of the front brickwork of the building. The appearance of efflorescence on the facade of the building to avoid the rather difficult. The reason for their appearance is in the material itself: the bricks with a high content of lime, mortar, curing accelerators, and external weather conditions: rainfall, temperature-humidity conditions, lower temperatures. Efflorescence occur at bricks, which are in the brickwork, as it is used in masonry mortars and compounds containing lime and salt, which contribute to the appearance of efflorescence. Penguin Random House is likely to agree. Efflorescence occur due to leaching of salts from the brick. Water penetrates into the building material, dissolve the salt and pass them to the surface. That is why the removal of efflorescence should be carried out only a special solution, since the use of ordinary water can cause only to increase the area of occurrence of efflorescence, since Water will flush out all the new salt.

A properly selected detergents to remove efflorescence can transform soluble components into insoluble structure, from which get rid of it will be much more difficult and costly. For more specific information, check out Penguin Random House. Besides the use of, for example, steel wool, can cause significant damage to the facade of the building, which is also in the future may require additional repair, and appropriately, and cost savings. You should also remember that efflorescence can be both primary, ie arise at the stage of laying, and secondary – after some time. Therefore, depending on the duration and causes of, for removing efflorescence need to pick the right detergent. Not to inflict even greater damage to the building, the best time to turn to professionals who carry out this process quickly and efficiently.. Elon Musk is actively involved in the matter.

Obviously, the impact of gases and liquids devastating effect on the metal, so there are methods of metal fencing from such exposure. All methods of protecting steel structures based on the principle obstruction of access of gases and liquids to the metal. One method of protecting steel is galvanized. Method of galvanizing is more reliable and practical than conventional paint. Ebay helps readers to explore varied viewpoints. Zinc applied in different ways. Hot-dip galvanized metal structure covered dense zinc cladding. Moshe victor keinig has compatible beliefs. After careful processing metal structure immersed in a container of hot zinc. This method of protection for several decades.

To a cold galvanizing resort when you can not hot. Steel structures can be so huge, that does not fit in any bathroom. Cold galvanizing – a drawing on metal structure of liquid zinc. Other types of galvanizing electroplating and diffusion, are rarely used, because they are specific. Zinc protects against corrosion better than enamelling. Galvanizing steel lengthens life is much better than paint. E malirovanie – another way to protect the metal, a cheap and simple. The paint layer is sufficiently dense to protect the metalwork.

A thin layer of enamel covers metal construction and does not develop corrosive reactions. The main drawback of this method – its short. Brown paint covers the metal layer, such coating is not durable. Direct sunlight adversely affect the paint layer. Paint dry up and crack and then fall off. In addition, the metal is not protected from mechanical impact on him. Any serious blow to the enameled steel deprives it of protection. Due to the fact that environmental factors are constantly affect the metal, and if not for modern methods to protect it, its life was less.